Filters
The Influence of Temperature on Rheological Parameters and Energy Efficiency of Digestate in a Fermenter of an Agricultural Biogas Plant
This investigation specifically aims to enhance the understanding of digestate flow and mixing behavior across typical temperatures in bioreactors in agricultural biogas plants, facilitating energy-efficient mixing. Experimental tests confirmed that digestate exhibits non-Newtonian characteristics, allowing its flow behavior to be captured by rheological models. This study validated that digestate rheology significantly varies with temperature, which influences flow resistance, mixing efficiency and overall energy requirements. Two rheological models—the Bingham and Ostwald models—were applied to characterize digestate behavior, with the Ostwald model emerging as the most effective for Computational Fluid Dynamic (CFD) simulations, given its balance between predictive accuracy and computational efficiency. Specifically, results suggest that, while three-parameter models, like the Herschel–Bulkley model, offer high precision, their computational intensity is less suitable for large-scale modeling where efficiency is paramount. The small increase in the accuracy of the shearing process description does not compensate for the significant increase in CFD calculation time. Higher temperatures were found to reduce flow resistance, which in turn enables increased flow rates and more extensive mixing zones. This enhanced mass transfer and mixing potential at elevated temperatures are especially pronounced in peripheral areas of the bioreactor, farthest from the agitators. By contributing a model for rheological behavior under realistic bioreactor conditions, this study supports the optimization of energy use in biogas production. These findings emphasize that temperature adjustments within bioreactors could serve as a reliable control strategy to maintain optimal production conditions while minimizing operational costs.
Diversification of macrophytes within aquatic nature-based solutions (NBS) developing under urban environmental conditions across European cities
Hydrological Effects of the Planned Power Project and Protection of the Natura 2000 Areas: A Case Study of the Adamów Power Plant.
The planned construction of a steam–gas unit at the Adamów Power Plant raises questions about the potential hydrological impact on the neighboring Natura 2000 protected areas, particularly the Middle Warta Valley (PLB300002) and the Jeziorsko Reservoir (PLB100002). These ecosystems play a key role in protecting bird habitats and biodiversity, and any changes in water management can affect their condition. This paper presents a detailed hydrological analysis of the Warta River and Jeziorsko Reservoir for 2018–2022, with a focus on low-flow periods. The Peak Over Threshold (POT) method and Q70% threshold were used to identify the frequency, length, and seasonality of low-flow periods in three water gauge profiles: Uniejów, Koło, and Sławsk. The longest recorded low-flow episode lasted 167 days. The permissible water intake for the investment (up to 0.8 m3∙s–1) is in accordance with the applicable permits and is used mainly for cooling purposes. Calculations indicate that under maximum intake conditions, the water level reduction in the Jeziorsko Reservoir would be between 1.7 and 2.0 mm∙day–1, depending on the current level of filling. Such changes do not disrupt the natural functions of the reservoir under typical conditions, although during prolonged droughts, they can pose a threat to protected areas. An analysis of the impact of periodic water overflow into the Kiełbaska Duża River indicates its negligible effect on water levels in the reservoir and flows in the Warta River. The results underscore the need for the integrated management of water and power resources, considering the increasing variability in hydrological conditions. Ensuring a balance between industrial needs and environmental protection is key to minimizing the potential impact of investments and implementing sustainable development principles.
Beaver Dams as a Significant Factor in Shaping the Hydromorphological and Hydrological Conditions of Small Lowland Streams
Beavers play a key role in creating temporary water reservoirs that significantly impact the natural environment and local river hydrology. The primary aim of this study was to assess the potential of increasing the number of beaver dams (Castor spp.), as an alternative method of water retention in the environment. Research conducted on three small lowland streams in central Poland revealed that beaver dams, even in modified riverbeds, enable the formation of shallow floodplains and ponds. Innovative analyses considered the structural materials of the dams and their impact on river hydromorphology and sediment transport. The findings emphasise the importance of beavers in water retention processes, the stabilisation of water levels during low flows and the protection of biodiversity. The study also demonstrated that beaver dams play a critical role in storing surface- and groundwater, mitigating drought impacts, reducing surface runoff, and stabilising river flows. These constructions influence local hydrology by increasing soil moisture, extending water retention times, and creating habitats for numerous species. The collected data highlight the potential of beaver dams as a tool in water resource management in the context of climate change. Further research could provide guidance for the sustainable utilisation of beavers in environmental conservation strategies and landscape planning.
The Use of a Multi-Criteria Decision Analysis Method to Select the Most Favourable Type of Fish Pass in Mountainous Areas
Fish passes are a key element enabling the migration of aquatic organisms in the context of restrictions resulting from the presence of weirs. Multi-criteria decision analysis, AHP, and Rembrandt methods were used to assess the effectiveness of fish passes on mountain rivers. Three common types of fish passes were considered: slotted fish pass, block ramps, and a circulation channel with boulders. The results of the study indicated that block ramps proved to be the most favourable solution, achieving the highest preference values in both methods (Rembrandt: 0.77, AHP: 0.63). The key factors influencing the effectiveness of the fish passes are the availability of space and the water requirements, which reached values of 0.38 and 0.27 in the Rembrandt method and 0.33 and 0.28 in the AHP method, respectively. The differences between the results of both methods were minimal and did not have a significant impact on the final choice. The discussion emphasised the advantage of nature-like fish passes, such as block ramps, which better preserve the ecological continuity of rivers and can be more easily adapted to local hydrological conditions. The study also indicated the need for continuous monitoring of the fish passes and their optimisation to reduce problems related to sedimentation and flow blocking. The obtained results can provide a valuable basis for decision making in the planning and construction of fish passes, especially in demanding mountainous conditions, contributing to improving the effectiveness of fish migration and minimising negative impacts on the natural environment.
Analysis of the Influence of Hydraulic and Hydrological Factors on the Operating Conditions of a Small Hydropower Station on the Example of the Stary Młyn Barrage on the Głomia River in Poland
The operation of water structures causes various problems. They are related, for example, to the material carried by the water, hydrological conditions, range of operation of hydroelectric turbines, or water elevations at the lower position of the hydroelectric power plant. Among the various operational problems, this article focuses mainly on the impact of the backwater of Gwda river on the water level elevations at the lower station of the Stary Młyn hydropower plant in Dobrzyca. The power plant is located on Głomia river. The analysis was carried out for different flow variants in both the Gwda and Głomia rivers. The effect of characteristic flows on the water surface level at the lower station of the hydropower plant was examined. It was found that the water surface level at the lower station of the hydropower plant is strongly influenced by flows higher than the average high flow on Gwda river. Due to the extent of the backwater in current operating conditions, the hydroelectric power plant is shut down from flows on Gwda river of 30–28 m3/s (flows that are not much higher than the multi-year average SSQ). The modeling results were confirmed by an analysis of power plant shutdowns of normal operation especially in wet years, when the plant did not operate for almost half of the year (188 days), with losses of 203 MWh. It was also shown that even a small additional damming of water, e.g., of the order of 0.2 m, can extend the operating time of a power plant up to 249 days even under unfavorable hydrological conditions. Factors related to climate change are beginning to play an increasingly important role in the current operating conditions of small lowland hydroelectric power plants. They can contribute to a reduction in electricity production. The proposed solution related to the possibility of greater water retention on dammed-up water barrages allows one to partially offset these problems as well.
Woda w środowisku miasta - dobro strategiczne wobec rosnącej antropopresji i zmian klimatycznych
Chitosan/Perlite System as a Microbial Carrier in Anaerobic Digestion of Food Waste: Characteristics and Impact of the Additive Materials
The article aims to present the results of research on anaerobic digestion (AD) of waste wafers (WF - control) and co-substrate system - waste wafers and cheese (WFC - control), combined with digested sewage sludge. The aim of the study was to evaluate the physicochemical parameters of the chitosan/perlite (Ch/P; 3:1) carrier material and to verify its effect on the directions of change of the bacterial microbiome, removal kinetics of organic matter and AD process efficiency. The experiment was conducted in a laboratory, in a periodical mode of operation of bioreactors, under mesophilic conditions. The results of analyses of morphological-dispersive, spectroscopic, adsorption, thermal and microbiological properties confirmed that the tested carrier material can be an excellent option to implement in biotechnological processes, especially in anaerobic digestion. The microstructural properties of the carrier were influenced by both components: perlite determined the development of the specific surface area, while chitosan shaped the porosity of the system. The thermal properties were determined by the less heat-resistant component, present in a threefold higher weight proportion, i.e. chitosan. The evaluation of quantitative and qualitative changes in the genetic diversity of bacterial communities, carried out using Next Generation Sequencing (NGS), showed that the material has a modifying effect on the bacterial microbiome. Amount of bacteria from phyla Actinobacteria, Bacteroidetes, Campilobacterota, Chloroflexi, Euryarchaeota, Planctomycetes, and Proteobacteria decreased while Firmicutes, Synergistetes, and Thermotogae increased during the course of the experiment. The shapes of the FT-IR spectra indicated a dependence of the degradation rate on both the presence of the carrier and the cosubstrate system. Monitoring of the course of AD was carried out by measuring key parameters for the stability of the process: pH, VFA and VFA/TA ratio (volatile fatty acids/total alkalinity). As a result, an increase in the volume of biogas/methane produced, under the influence of the carrier, was recorded for WF-control by 12.05% and for WFC-control by 19.16%. The volume of methane for the WF-control increased from 351.72 m3 Mg-1 VS to 411.14 m3 Mg-1 VS, while for the cosubstrate sample it increased from 476.84 m3 Mg-1 VS to 518.08 m3 Mg-1 VS, confirming the validity of combining the respective cosubstrate with microbial carrier in anaerobic bioreactor.
Influence of river channel deflector hydraulic structures on lowland river roughness coefficient values: the Flinta river, Wielkopolska Province, Poland
Environmental Restoration and Changes of Sediment and Hydrodynamic Parameters in a Section of a Renaturalised Lowland Watercourse
In Europe, the routes of most watercourses were straightened and shortened, leading to the destruction and degradation of many natural environments. Currently, in places where it is possible, as part of the implementation of the Water Framework Directive, efforts are made to improve environmental sustainability, including improving the ecological condition of rivers. This paper presents the impact of three in-stream deflectors on changes in the section of a small lowland river—the Flinta (Poland)—where (from 2018 to 2023) detailed, systematic geodetic, and hydrometric research and an assessment of the ecological conditions were carried out. The presented results show the influence of deflectors on the initiation of fluvial processes in the transverse and longitudinal layouts of the channel. The river channel was narrowed from 6 to 5 m, and the current line shifted by almost 3 m. Changes were observed in the distribution of velocities and shear stresses, varying along the surveyed section of the river. In the first year after their application, an increase in velocity at the deflectors can be observed (from 0.2 m∙s−1 to 0.6 m∙s−1 in the deflector cross-section). In the following years, on the other hand, a clear decrease in velocity was observed in the sections between the deflectors (to 0.3 m∙s−1). The introduction of deflectors resulted in a significant increase in the values of shear stresses (from an average value of 0.0241 N∙m−2 in 2018 to 0.2761 N∙m−2 in 2023) and local roughness coefficients (from 0.045 s∙m−1/3 before the introduction of the deflectors to 0.070 s∙m−1/3 in 2023). Based on analyses of sediment samples, erosion and accumulation of bottom material were initially observed, followed by a subsequent stabilisation of particle size. Differences in grain size were observed, especially in the cross-section of the deflectors (increase in granularity d50% downstream of the deflector from 0.31 mm to 3.9 mm already 2 years after the introduction of deflectors). This study confirmed the positive impact of using deflectors on hydromorphological processes as deflectors facilitate the achievement of a good ecological status, as required by the WFD. The innovation of this paper lies in demonstrating the possibility of using small, simple structures to initiate and intensify fluvial processes, which may contribute to improving the ecological conditions of watercourses.
Fit for Purpose—Analyses of Macroinvertebrate Communities for Environmental Flow Assessment
ABSTRACTEnvironmental flow assessment is crucial for sustainable water management. In assessing environmental flows using the most common methods, for example, habitat suitability modelling (HSM), it is assumed that the distribution of aquatic organisms is driven by hydraulic features and substrate type of the habitats. However, most of the existing research does not consider analyses of organisms' ecological traits and their community structure. To bridge this gap, we present the results of analyses of macroinvertebrate communities carried out for environmental flow purposes. The study was performed at two reaches of the Flinta River, a European, lowland, temperate and perennial river, with different degrees of hydromorphological alterations. We state that more detailed analyses of organisms' community in environmental flow assessment are needed. Thus, we assess the dissimilarity of the organism community structure sampled during field campaigns by means of statistical tests, and we analyse macroinvertebrate ecological traits and indicators commonly used to evaluate river status. Afterwards, we discuss the applicability of the analyses and provide recommendations for the future environmental flow assessments.
Opportunities for the Transformation and Development of Power Plants Under Water Stress Conditions: Example of Adamów Power Plant
In the vicinity of the Adamów power plant, which operates in the catchment area of the Kiełbaska river, there is a significant shortage of water resources caused by the intensive use of water by the energy industry and agriculture. The development of the plant by replacing the outdated coal-fired (lignite-fired) units with modern gas and steam units may contribute significantly to reducing the negative impact on the environment and reduce the demand for water resources relative to coal technology. Gas and steam units are a much more energy-efficient technology. This implies a lower demand for water, a reduction in pollutant emissions, and greater operational flexibility, which enables the units to adapt to changing hydrological and environmental conditions. The high efficiency of these units limits the need for frequent water-refilling, while allowing for a more sustainable and stable production of energy. Based on an analysis of hydrological data for the years 2019–2023, it was estimated that water stress is observed in this catchment area on 198 days per year, which accounts for c.a. 54% of the hydrological year. Therefore, it is assumed that inter-catchment pumping stations with a flow of 0.347 m3∙s−1 will be required. This sets the demand for water at 5.95 million m3 per year. The planned water transfer will be carried out from Jeziorsko reservoir on the Warta river through the catchment area of Teleszyna river. Moreover, there are plans for the reconstruction of the layout of Kiełbaska Duża and Teleszyna rivers, which would involve the restoration of natural run-offs, following the discontinuation of open-pit lignite mining. This will additionally be supported by the reduced demand for water in the water use system when using the modernised power plant. The analysed data made it possible to develop hydrological scenarios that take the future reduction in water stress into account by implementing plans to restore the former hydrographic system in the region. These investments would also foresee the creation of new retention reservoirs (in former mining pits) with a capacity of nearly 900 million m3, which will significantly increase the region’s water resources and retention potential, supporting hydrological and energy security for the years to come.
Biofilm Formation and Genetic Diversity of Microbial Communities in Anaerobic Batch Reactor with Polylactide (PLA) Addition
In this paper, an anaerobic digestion (AD) study was conducted on confectionery waste with granular polylactide (PLA) as a cell carrier. Digested sewage sludge (SS) served as the inoculum and buffering agent of systems. This article shows the results of the analyses of the key experimental properties of PLA, i.e., morphological characteristics of the microstructure, chemical composition and thermal stability of the biopolymer. The evaluation of quantitative and qualitative changes in the genetic diversity of bacterial communities, performed using the state-of-the-art next generation sequencing (NGS) technique, revealed that the material significantly enhanced bacterial proliferation; however, it does not change microbiome biodiversity, as also confirmed via statistical analysis. More intense microbial proliferation (compared to the control sample, without PLA and not digested, CW–control, CW–confectionery waste) may be indicative of the dual role of the biopolymer—support and medium. Actinobacteria (34.87%) were the most abundant cluster in the CW–control, while the most dominant cluster in digested samples was firmicutes: in the sample without the addition of the carrier (CW–dig.) it was 68.27%, and in the sample with the addition of the carrier (CW + PLA) it was only 26.45%, comparable to the control sample (CW–control)—19.45%. Interestingly, the number of proteobacteria decreased in the CW–dig. sample (17.47%), but increased in the CW + PLA sample (39.82%) compared to the CW–control sample (32.70%). The analysis of biofilm formation dynamics using the BioFlux microfluidic system shows a significantly faster growth of the biofilm surface area for the CW + PLA sample. This information was complemented by observations of the morphological characteristics of the microorganisms using fluorescence microscopy. The images of the CW + PLA sample showed carrier sections covered with microbial consortia.
Preparation of Samples for the Study of Rheological Parameters of Digested Pulps in a Bioreactor of an Agricultural Biogas Plant
The studies of the rheology of digested pulp from agricultural biogas plants have often been fragmentary and non-standardised due to their complexity and time-consuming nature. As a result of measurements, it was possible to develop a procedure and range of measurements for the correct determination of the parameters of the carrier substance. The applicability of the coaxial cylinder measurement system was demonstrated for assessing the rheological parameters of digested pulp from a fermenter that utilises agricultural biomass. To determine the characteristics of solid particles, the Zingg diagram was used, inter alia, allowing the comparison of particles from each fraction. The analysis of the shape and size of solid particles may help to describe the onset of motion of this phase, flow type, or sedimentation type. The authors propose a completely new research approach to obtain an appropriate, repeatable test conditions of medium, which is the carrier liquid from the biogas plant reactor. The proposed methodology and the scenario of the entire study make it possible to achieve scalable and comparable test results in any laboratory. The proposed solution eliminates the influence of most external factors on the sample and rheological measurements, and the effectiveness of the presented procedure was confirmed in tests.
The use of sewage sludge in anaerobic digestion process: formation, properties, and implementation.
The effect of municipal wastewater treatment, in addition to improving its quality, is sludge formation. Disposal of sewage sludge (SS) is a critical environmental problem that requires careful management. Under current legislation, SS represents waste requiring stabilisation to eliminate pathogenic microorganisms and substances potentially harmful to the environment. Anaerobic digestion (AD) is an efficient method of treating SS, and it produces biogas as a renewable energy source (RES). The efficiency of the process can be increased by combining SS with other organic wastes as cosubstrates. Therefore, AD allows for a twofold benefit crucial for sustainable waste and energy management, i.e. sludge stabilisation and biogas production. Another equally important consideration in the construction of biogas plants at wastewater treatment plants is reducing the plant's operating costs by using the electricity and heat generated in the cogeneration units for the plant's needs. This paper discusses the formation technology and properties of sewage sludge, the legal aspects of using and disposing of SS, the conditions for employing their anaerobic biodegradation, and the co-digestion systems used.